Easter Joyride!!

Come along for an Easter Joyride in the Coupe! We took a few spins around the neighborhood and two very short runs out onto the main road. The wind noise is high because we do not have the windshield in place: video

We wired the headlights and front turn signals this week.


We also wired the reverse light (in the license plate frame) and the license plate illumination lamp.

We were working on the rear hatch plexiglass when we ran out of time. Maybe we'll have pics of that next week. 'Til then!

Lots of Little Things There's no point in taking pictures of things you can't really see. This week we decided that we'd had enough of the brake master cylinder we bought last summer. Try as we might, it appears that the remanufactured cylinder wasn't going to pressurize brake fluid so that we could bleed it. With a new master cylinder installed, the brakes now feel great, but we gave up much of Saturday to get this done. We pulled the fuel injectors and shipped them off to a vendor who cleans and rebuilds them. With the top of the engine off to get to the injectors, we took the opportunity to burp the engine of some air that was preventing the radiator fan switch from coming on. We also snugged up a line that weeps a little coolant when the engine is warm. We secured wires under the hood and in the passenger footwell. We installed the shift knob and charged the battery in anticipation of a test drive when the fuel injectors return this week. We tried to install the exhaust pipes, and learned that the side pipes need to be stretched a little to fit over the exhaust headers. Off to the muffler shop! We're down to a short list of things that need to be installed before we start on the body work. Anything that requires holes to be drilled in the body will need to be temporarily installed before we start sanding and painting. These include wipers, rear hatch, spoiler, exhaust, headlight covers and side mirrors. We're getting close!

Two Scoops!

Lots of pictures this week. Remember, you can click on a picture to get a better look.

We decided to use the rear window scoops after all. On the original cars, these fed a rear brake cooling duct. On our car, they will scoop fresh air in through our opening scoop windows to cool us off on mild days. When it gets hot, the windows will close and we'll run the air conditioner!

We were not pleased with the mount on the hood for the hood struts. These keep the hood open when it is raised, and the hood side of the strut was mounted to some styrofoam board with fiberglassed mat over it. The problem is, they didn't put enough fiberglass on it. You can actually see the styrofoam in this picture. We added an aluminum piece with three extra mounting bolts to really hold it well.

We finished installing the bottoms of the hood. These are needed to provide for a locating pin and hole (the hole is just visible on the left edge of this picture). The pin is an acorn nut installed on the body where the hood settles on. We also marked and trimmed where the hood meets the cowl one last time to get a nice consistent gap. Those large aluminum pieces hanging from the hood are the upper splash guards that you saw last week with the hood closed.

As promised, here is a pic of the installed seats. They're not much to look at without the upholstery, but that is staying in a sealed bag until the painting is all finished. The seats do face away from the centerline of the car a little, but they're in just the right place!

We drilled the dash supports and installed the dashboard. We also drilled some holes to hold the switch panel in place. Picture those surfaces covered in a pebbly black truck bed liner, as that's the plan.

One final picture to hold you over until next week. Thanks for checking in!

Another Good Week!

We set our sights on some more noticeable changes this week. We assembled and installed the headlights and front turn signals.

The upper splash guards provided with the kits are a couple of inches too small to actually seal off the engine compartment. A local metal shop bent some oversize pieces of aluminum, and with a bunch of marking and cutting we were able to come up with pieces that fit!

Under the car, a long narrow piece of aluminum connects two triangular sections that help funnel air into the radiator when it comes through the opening in the front bumper. That strip of aluminum looks like it'll flap in the wind, so we came up with an idea to tie it to a more solid piece of aluminum a few inches behind it. No one will ever see it, but we're happy with the improvement.

We dropped the windshield on just to make sure we hadn't distorted the body along the way somewhere. When the time comes, we will have it professionally installed. Interestingly, the windshield shape comes from a 1986 Jaguar XJS. I wonder how many windshields they had to look at to find that one? :-)

We won't have pictures until next week, but we also installed the seats and started the process of fiberglassing the bottom edge of the hood back on. We had cut it off earlier to size the hood correctly. It's our first effort with fiberglass, but so far it is going well.

In the coming weeks, we will be winding up construction. We need to fit the exhaust pipes, install the rear hatch, drill for the windshield wipers, fit the spoiler, and install the mirrors.

We will then have a punch list of things to go back and address before we start smoothing out the body itself. With any luck, we'll be painted and on the road by September.